VINTAGETRACTORS.COM
AND
RUSTY ACRES RANCH
Engine Parts
for IHC Farmall Cub tractors
Original Cub carburetor (#1), very good condition,
was removed from a running engine, $160
Original Cub carburetor (#2), very good condition,
$150
Two views of a Cub J4 magneto. Turns freely and looks
to be in good condition, but not tested, $75
Spark plug wire holder, $9
Cub starter #1, works great, came from a running engine,
$175
Cub starter #2, works great, $175
This is a new float for the Cub
carburetor. I ended up not needing it. $18
Cub head in great condition,
$70
Cub head in great condition, $70
Cub manifold #1, very nice, $60
Another nice manifold #2, $60
Cub manifold #3, good condition,
$40
Cub manifold #4, good condition, $50
Cub manifold gaskets, $5
.030 over cast iron Pistons: $20 each, 6 available
.030 over aluminum piston, one available, $15
.060 over cast iron piston, four
available, $25 each or $85/set of four
Connecting rods, $20 each, $75 set of four
Cub block #3, Casting #251341R1,
for early Cub, no vvisible cracks or repairs, .030 over (matching
pistons available), $120, can ship UPS
Good crankshaft matched to Block 3, with used main bearings, $50
Cub block from a running tractor,
no breaks, cracks, or repairs noted. Bored .060 (matched to the
pistons shown above, matching crankshaft also available). Casting
#251341R1, for early Cub. $120 (Can ship UPS, 105 lb)
Cub block. It does have a freeze
crack on the outside at the area circled in yellow. The crack
was covered with bondo, which I removed to show the extent of
the crack. Bores and valve seat areas look good. $40, can ship
UPS.
Valve set with springs and keepers,
$50 (Two of the valve lock retainer halves are missing)
Valve lifters, $7 each, set of
8: $45
Idler gear shaft, $25
Idler gear, $35
Camshaft, $45
Camshaft gear, $45
Both for $80
Oil pump, $40
Screen for oil pump, $25
Pickup tube for oil pump, $10
Original oil gauge, $15
Oil filter cover and bolt, $10
Front engine cover, greasy, but
no breaks or repairs, $30
This front engine cover has a
brazed repair, $10
Oil pan, $12
New oil pan gasket, $6
Rear engine seal and housing,
$12
Good crankshaft, $50
Crankshaft pulley, $40
Crankshaft pulley with a chip
as circled in blue< $15
Flywheel with ring gear, $60
Cub internal governor parts,
$35
Control parts for Cub governor,
$15
Cub governor, $50
Distibutor and mounting bracket, $60
Coil with bracket, $15
Dipstick and breather cap (Cap is modified), $8
Good dipstick, no modifications, $15
Cap, $6
Valve cover, $10
Cub flywheel shield, $15
!
Front end and radiator support with serial tag (steering
gear housing), no breaks, no repairs, excellent condtion. $200
Front end and radiator support, has a leak along the
front (see the silicone sealant in the photo), $40
Front end and radiator support with serial tag # FCUB3154
(Steering gear housing), no breaks, no repairs, excellent condtion.
$200
Poor radiator, Free with any parts order
Radiator sides, $20 each
Throttle rod, $15
Carb to governor rod, $10
Throttle lever assembly, $25
Starter and choke rods, $20 each
Amp gauge, $5
Original switch and knob, $25
Generator, $75
Generator, $75
Generator adjusting strap, $12
Generator Bracket, $13
Lower Water pipe, $25
Upper water pipe, $20
Nice fan assembly, $65
Nice fan assembly, complete,
$65
Fan assembly, bearing needs some
attention, $25
Cub fan, $5
Cub brackets, $3
